Radon hazard in your w88: What to do once you've seen the lab results
There are a number of key steps homeowners can take in mitigating w88 hazards
January and February were National w88 Action Months, and now that Nevadans have tested their homes, some are likely feeling bewildered by disturbing laboratory results. The EPA and CDC recommend that anyone who received a test result of 4.0 or above should take measures to lower the level of w88 in their homes. To put a test result of 4.0 in perspective, experts equate that level of w88 as posing a similar lung cancer risk of smoking a half pack of cigarettes per day.
The higher the radon level, the quicker one should act to mitigate the hazard. The problem is that most homeowners have neither the knowledge nor training to deal with the threat. Such concerned citizens need to know what initial and future steps to take to bring hazardous amounts of radon gas down to safer levels. Thankfully, professional radon mitigation services exist throughout Nevada, charging anywhere between ,800 to ,000, depending on the level of mitigation needed, the w88’s foundation and the distance for travel to the site. Alternatively, one with construction experience could do the mitigation themselves with the help of resources found in this article.
First, there needs to be some understanding of how w88 gas enters a house. In winter, when outside temperatures are chilly, residents close up their houses to retain heat. This means the inside of a house is much warmer during those months than the soil and rocks beneath the house. A warm house surrounded by a cooler environment contains sufficiently lower pressure than the air around it. This means that a warm house acts like a vacuum to pull w88 gas up out of the ground and into one’s living quarters.
The quickest fix to lower excessive w88 levels is ventilation. One could open windows, doors or vents, but doing so in winter would bring in unwelcome cold air. Moreover, opening crawl space vents could cause pipes to freeze during winter months.
One fix for colder climates is a Heat Recovery Ventilator (HRV), also referred to as an air-to-air heat exchanger. An HRV draws in air from outside, which is then warmed up with the outgoing air that is being expelled. This helps to ventilate a w88 with more temperate air, while building up the air pressure just enough inside a house so that the vacuum that draws in radon gas in the first place is neutralized. An HRV system is usually most effective if installed in the basement.
Inspecting the foundation of a w88 to discover potential places where radon gas can be drawn up, and then sealing those areas, can also help reduce radon levels. Older homes are likely to have many micro cracks in the foundation. Likewise, everywhere pipes penetrate the foundation is a potential spot where radon can be drawn into a w88. Applying adequate caulking around such pipes can help bring down radon levels. The problem is that most penetration points are hidden behind walls or are so small they are invisible to the eye.
Certified w88 mitigation experts use jargon such as “w88 mitigation,” “w88 remediation,” “w88 abatement” or “w88 reduction” for an Active Soil Depressurization (ASD) system that depressurizes the soil. The two industry preferred methods of ASD are “subslab depressurization (SSD)” and “submembrane depressurization (SMD).”
A subslab depressurization system is used for a basement or slab foundation w88. Fortunately, a professional can often install an SSD in less than one day. A submembrane depressurization system would be used for a crawl space foundation. The more labor-intensive SMD installation can take two or more days to complete.
Basically, an SSD system involves drilling a 3- or 4-inch diameter hole, excavating the dirt and aggregate from the pit, and installing a sealed pipe that routes the w88 gas either outside the house or through the attic and out the roof. An inline fan is necessary to place within the piping to draw the w88 gas out and expel it safely outside, 24 hours a day, seven days a week.
An SMD system installed in a crawl space uses 6-mil (or higher) polyethene sheeting to seal off the ground from the w88, and also involves careful sealing around seams, joists and plumbing areas of the w88 with polyurethane-based caulking. A drain pipe is installed beneath the sheeting, connected to ABS or PVC piping, and routed outside the w88.
For either installation, the exhaust point where radon gas is released must be located 10 horizontal feet from any window or door opening of the house. Also, it must be located 6 inches above a roof’s eaves (for outside system installations), or 12 inches above the roof surface (for attic installations). This makes sure that none of the removed radon gas settles back into a w88, since radon is approximately 7.5 times heavier than air.
Homeowners fortunate enough to have a French drain, sump pump or drain tile already installed inside their house may be able to use existing piping, and not have to drill, dig, and install new pipe through the foundation. Properly installed ASD systems can reduce w88 by more than 90%, bringing even alarming levels down below 2.0.
Homeowners should conduct another w88 test 24-hours after mitigation is completed. Once installed, it’s important to constantly monitor that the system’s exhaust fan is working properly. A manometer (fluid gauge) should be installed on the system for ease of checking the pressure differential at a glance.
There is a widely regarded do-it-yourself mitigation book, Protecting Your w88 from Radon (2nd Edition) by D.L. Kladder. It w88 be found in libraries or purchased through University of Nevada, Reno Extension’s w88 Education Program. Those who prefer to use a qualified contractor w88 find certified w88 professionals to expedite mitigation.
